Weber 67820 - 3 Burner Tube Set For Genesis 300 Series Grills (2008 - 2010), 34-1/4" Long

Like another reviewer mentioned, replacing this burner tube set would have been a really easy job...20-30 minutes I'd say, had the bolts holding the old one in place not been so rusted. Despite the fact that I soaked them in penetrating oil, 2 bolts snapped almost immediately when I tried to remove them. Rather than try to remove the snapped off screws, I drilled pilot holes and then used (stainless steel like they should have been in the first place) self tapping screws and it worked like a charm.That being said, I was prepared for that possibility and still finished in around 45 minutes. The instructions were clear and the tubes were a perfect fit for my 2010 Genesis 300. I replaced them when my back 2 burners would no longer ignite. Towards the end before the back two quit on me completely I would have to hit the ignite button for each burner. Now once I get the first burner going they all light as soon as I turn on the gas to them just as they did when the grill was brand new. As a bonus, my grill heats more evenly now and the max high temp I am able to achieve went up by at least 30 degrees. I wish I had done this at least a year ago!

What a difference! After 14 years of heavy usage the burner bars on my Genesis 300 have rusted out completely. Watched a YouTube video and found out replacement is a snap. I love these Burner tubes! The installation was a challenge. The 3 screws holding down the tubes were almost impossible to remove. WD 40 wouldn't get them to budge. Couldn't use a driver, my power equipment couldn't get the screws to turn, and I spend a frustrating 30 minutes. Finally decided drastic action was needed. Using a flathead driver, I was able to bend the bar and slide it out from under the screw. The bars where completely rusted out and bent without much effort. Using my vice grip, I was able to grab hold of the screws and force turn them.Once free - installation was simple. Slide the bar out of the temperature control feeder tube and insert the new bar. The challenge came with the cross tube. After much effort and some wrestling the thing finally went into their place. New screws with the kit finished thing off. Reconnected the propane line and the grill lit on the first try. No flareups, even cooking, great taste. Should have done this sooner.

Only pain was removing the old screws on the old burners. Had to use a cutoff saw to reove the screw heads, and drill out the old screw shanks. Otherwise, fit was perfect. My weber had not worked this well for a few years. Was just like new for the flame output.

Replaced the burners on my Genesis with these after my original transfer tube (which lights the middle and rear burners) rusted out.New burners are great and do exactly what you’d expect. They work as well as my grill did when it was brand new. No more hot spots or flare-ups. Just nice even heat, and the grill heats up much quicker than it did before the replacement.Other reviewers mention that you don’t realize just how bad your old burners are until you replace them - and it’s true.My biggest gripe is not with this product, but with the hardware on the grill. The two screws (on the outside of the bottom grill pan) that hold the manifold in place (and which you need to remove to replace the burners) wouldn’t budge, and the heads sheared off both when I tried to remove them. If yours come out? Then install is straight-forward enough and the instructions are easy to follow.Great product. I probably should’ve bought these years ago.

The original burner was beat after about 12 years, which is pretty good. This is the correct burner for the Weber Genesis with the controls on the right-hand side. I chose the actual Weber brand unit because I knew it would last a long time and because it is made in the USA. Several aftermarket brands, while somewhat less expensive, appear to be made in China. The hardest part was getting the old burner out, as the screws that hold it down to the grill's body were rusted and impossible to unscrew. I cut the heads off with a small cutting wheel, drilled out the rest of the screw, and re-tapped the holes to accept the new screws. My new burner seemed to be missing a screw out of three, so I used one of my own. Once in, everything operated fine, and the improvement in performance is quite noticeable. I am getting the same heat with a lower setting at the control. Because the burners last so long, it is likely that your screws will be rusted, too, and installation may be a little more effort than you would expect. None of that is the fault of this product. Most DIYers should have no problem. The results are worth it!

The package was an obvious return with the box re-taped and the small parts bag previously opened.It was missing one of the mounting screws. Easier to get from the hardware store than return item. The major components, the burners, were good quality and fit perfectly. The 2 (of 3 needed) screws included were too big for my mounting holes. No problem replacing them from the hardware store.Make sure to push the igniter assembly all the way in past the first resistance until it snaps into place.

Perfect replacement part. Easy to install and works great.

Installation was easier than I expected. The product was well packaged, informative and useful instructions included. Much more cost effective than buying a new grill