Rough Country Heavy Duty Rear LED Bumper for 2014-2021 Toyota Tundra - 10778

Good looking and solid. I like the steps in the bumper and the led cube lites are bright. Took a bit of work to install.A few points… there are led license plate lites that pass thru the screws, some ask if there are plate lites. There are. They have to be spliced into the old wiring. You need 22 gauge butt connectors, heat shrink tubes, and a heat gun to do it right.The cube lites… if you want them as an accessory lite then you will have to run the wiring to the cab so you can switch them on demand. I spliced mine into the reverse lite so they only come on when I go into reverse. So I have the reverse lites in the bumper and the ones built into the turn signal. Same as the license plate lite… 22 ga butt connector. But I did not heat shrink just taped up connectors because the connection was made inside the turn signal lens and will stay out of the yttihs Iowa weather and salt they dump all over the roads.The trailer wiring connector… it was a little bit of a bad feeling at first when trying to get the plug harness into the new bumper and it would not lock in, but did get it to click and lock in. Had to use a screwdriver and gently pry. Then when it was time to plug it in there was a bit of pulling to make it reach.Have a bunch of leftover washers and miscellaneous hardware, but they were not needed.Look up the install instructions online because the photos are in color and way easier to see images compared to the paper instructions sent with the bumper.Lame Iowa license plate registration sticker rules say lower left corner for sticker location. This bumper is blocking the bottom of the sticker now. It is one of those things the hero cops try to pull you over for to justify bs traffic stop. I really do not care if they pull me over for it or not, but some people should be aware of it if they have a reason they do care if they are pulled over.Two person job and at least one person should be knowledgeable about auto body work and wiring skills.

The bumper showed up well packaged, wasn’t that hard to install if you have a mechanical background. Took about 3-4 hours. Instructions were hard to read since they were photo copies but go on the website and you can see the instructions clearly. Overall a good buy.

I ordered this bumper to replace the plastic one on my 2017 TRD PRO. Bumper fitment to the truck is nice. It aligned well with the truck and looks good. The gap between the top of the bumper and the bottom of the tailgate is big. I think most of the aftermarket bumpers are this way. I installed a taillight light bar to occupy the space.The only dislike I have about the bumper itself is the placement of the factory trailer plug. In its current configuration, the 7 prong plug is on top and the 4 prong is on the bottom. It should be reversed. The 7 prong plug only goes in one way and is easy to install without seeing it. The 4 prong plug is harder line up and it requires seeing it to get it plugged in. Because it is on the bottom, you have to bend down to bumper level to see it. Not a deal breaker but it’s an inconvenience that could have been avoided.The license plate lights are are small led lights that go in place of the top plate screws. The wires on them are extremely thin and hard to work with. One of mine did not work from the get go.The bumper lights are super bright. One of mine had a chip in the finish. The supplied wiring kit is not long enough. You will need to get an additional extensions or cut and splice the wires. Since this wiring harness is included in a truck specific package, you would think the supplied wiring kit would be long enough.I am happy with the product and would by it again.i have received several compliments on it.

This was delivered within days. I was able to put it on in a few hours and it looks great on my truck.

Fits just like it should, only took 2 hours to to remove factory bumper,and install this bad boy! One light didn't work and they are sending me some replacements. Great product great customer service. I'm putting them in all my trucks!!!!

Fit my 17 toyota tundra sr5 double cab 4.6You will need a extra person to help hold the bumper when installing.

It’s an awesome bumper, lights are bright! Only down fall is when rough country made the bumper they did not account for were the bumpers height should have been in correlation to the plastic on the original bumper.

I had my trailer hit the back of my bumper when it came off my hitch didn’t even dent it