KrausRamus™ Single Handle Vessel Sink Bathroom Faucet in Satin Nickel, KVS-1007SN

The weight of this faucet is heavy, well made, easy to install and has the perfect reach for my oval vessel sink. It has a long enough reach that I can install it on the side of the sink instead of the front of it so I can put a medicine cabinet behind the sink...perfect!

This faucets are absolutely fabulous. However, the drain that came with them was advertised to fit on vessel sinks as long as the cabinet is thinner than 2 1/2 inches. My countertop was 1 1/2 inches and we ended up having to buy three new drains from Kraus to get the drain installed. Kraus refused to trade product or help us in anyway. They just blamed it on the installation of the sink we purchased. I guess you have to purchase a Kraus sink in order for their drains to fit as described. So we’re down an additional $140 to buy extended drains.

Beautiful faucet. Used with another drain after installation issues with the provided drain.

It's a perfect piece for my vanity . Simple but elegant and quality piece. The shade was a bit different than most of my brushed gold pieces but didn't clash . Worked well. Love it and recommend.

My wife and I love this. It's very appealing (to us) aesthetically, seems to be very well made and it works perfectly. For those who are DIY inclined: I found it easy to install.When installing, I ran into a minor problem that was totally my fault, but I'm mentioning it to prevent others from doing the same thing. It has 2 fastening mechanisms: (1) There's a plate with a 1 3/8 inch threaded hole and the bottom of the main tube is threaded. (2) The plate also has smaller threaded holes for two bolts that are tightened after the main tube has been tightened. Those two bolts are slotted for a Phillips screw driver and the installation instructions only mention that means of tightening them. The bolt heads are also hex shaped to accommodate a wrench for tightening. At first, I didn't even notice that the bolts could be tightened with a wrench, so I thrashed trying to use Phillips screw drivers---long, short,offset, whatever. The bolts were in a tight awkward position which I could only reach at full arm's length. While doing this, I noticed light reflecting from a flat surface on the bolt head and discovered that they had wrench-fitting hex heads. After that, I easily finished tightening them using a small quarter-inch ratchet, a short extension and an 8 mm socket.The installation manual and spec sheet are available on the Kraus USA web site, though it took some effort to find them. I would include links to them but, as I just learned, that violates Amazon's rules for submitting reviews.

nice looking faucet. simple. not so beautiful , simple and clean.very simple to install .

The faucet is stylish, easy to install and works well. However I had an issue with the fittings to the water supply. They constantly leaked and the washers supplied would not seal . They deformed after several attempts to get them to work, The washers became useless. So I went to my local hardware store and purchased bevel washers and pressed them into the 2 fittings. They worked perfectly, tight fit and no leaks. Cost about $2.00

I bought and installed 2 units. One worked fine but the other leaked where the supply lines joined the water supply faucets. Tried thread seal tape but that did not work. In the end I replaced that faucet with a Delta Trinsic, and was going to throw the Kraus faucet away but then I read about other reviewers having the same leaking issue and replacing the washers with Danco #7 O-rings. So will now keep the Kraus as a spare. It's amazing how a manufacturer will jeopardize a product by using a crappy part that probably costs cents in the manufacturing process.

Llego en perfecto estado, muy bien empacada! Un ligero rayón pero cosa de nada! Quedó Perfecto en el lugar, sólo fueron necesarios unos adaptadores para instalarla.

There aren't many choices on tall faucets for above counter vessels that's why I bought this. It's a good faucet although I don't really like the design. Wish there are more to choose from

I bought two of these. As shown in the attached picture, the manufacturer put strainers in-line at the attachment point which defeats the removeable, cleanable (or replaceable if needed) aerator/strainer at the faucet. When these in-line strainers plug with debris restricting flow (over time they will), service/cleaning is difficult assuming you remember they are there. It required me to make an avoidable trip/expense to acquire washers (also shown in the attached picture) to replace the in-line strainers. Had I known that, I would not have bought them. Really, they should know better.Also, the threaded stem that penetrates the counter top is much shorter than some competitors (and the faucet I'm replacing). In my case the 1.5" granite sits on a 0.5" cabinet (see attached photo). I had to discard the rubber washer to permit the metal washer & lock washer installation. Beware and measure first.

have install the faucette , but i have a probleme. The cold water run. But hot water do not work . can some one help me? Waiting for an answer please. Thank you!

I bought 3 Kraus products for my bsmt remodel. One kitchen sink, kitchen faucet and bathroom faucet. 3 for 3! They are crafted nicely. Beautiful solid sleek faucet. More than enough height for a vessel sink.