INJORAMB100-R80 20A Brushed Mini ESC for 1/24 1/18 RC Crawler Upgrade

I have two SCX24s and an older Panda Hobby Dodge, slow speed control was not good and the escs whined, real bad, especially the Panda Hobby esc. I was thinking of getting rid of the trucks, I have a bunch of 1/18th rigs, but instead found out about this inexpensive drop in replacement esc where you can keep the stock radios and receivers. I didn't want to drop a bunch of money on these rigs replacing so much. The MB100 works well, slow speed control is much better, and it is as quiet as a mouse. Hooking it up is very straight forward, plug your motor into the MB100 esc, plug the supplied cable from the MB100 to the stock esc/receiver channel 2, and finally plug your battery into the MB100 and you are good to go! If nothing works, check to make sure the plugs to and from channel 2 are in the right orientation. The only problem with the MB100 is where to put all of the electronics!!!!!! If you have a SCX24 buy the Injora aluminum side plate at the same time, you can mount the MB100 and battery on the plate or move things around as you wish. Without the side plate, I have electronics high up in the C10 cab, doesn't look cool and throws the weight balance off.Edit: This ESC has breathed new life into my SCX24s, the slow speed control with stock motor is actually really good, it has made it a pleasure to drive these rigs once again. The side plates did not help with placing the electronics in the C10, the MB100 would still not fit with plugs that stick out. To make the esc fit, I trimmed off the forward lip of the battery tray and placed Velcro in the tray. I then mounted the esc as for forward as possible with Velcro and mount the battery side ways, 90 degrees from the original orientation with Velcro also. I am sure it has slightly worse weight distribution now, but it is not obvious and it is worth if for the slow speed control.If you don't want to spend a bunch of money, but want to improve your SCX24 low speed control while using the stock transmitter and radio, get this esc. It is well worth it, I can't praise it enough.

Great esc! Bang for buck is up there with the best. Smooth,Slow crawl ability greatly improved over the stock esc. Only drawback for me was the terminals on the provided wire adapters,terminals are a bit bulky going into the esc. It's mostly because of my application, got the esc mounted on the side of the frame and the body clear but the terminals push against the body and take it off center. Still giving 5 stars because not everyone will have this small issue, some low profile terminals would make this esc even better!

If you don't want to go brushless these are the next best thing. Love how smooth they made your scx24 operate.

I wanted get my SCX24 Base Camp running smoother and quieter. I decided to save some dough and go this route, rather than the brushless conversion, and I'm glad I did! This ESC is silent compared to stock and it crawls so much smoother. I'm sure the purple 50T motor upgrade helps, but a night and day difference. You do need a new receiver to go with it. I used the Spektrum SLR300 with my stock STL2 radio.

Nice and quiet, runs smooth, nice control. Fit in my scx24 deadbolt with just a little trim on the stock mount plate

Fantastic. Nice and small so can be mounted anywhere. Adapters for most 2s batteries.

Did not think that switching from stock trx4m esc to this one and new radio could change a build so much. Increased the feel of quality and performance drastically

This made my day. Just received my Spektrum Firma brushless and installed it on my scx24 only to be so disappointed by how poorly it ran that it went right into the garbage.Purchased this esc and installed it with my original t50 and it works amazingly!!! 5stars all day long for the money. Stop reading and just buy it.I will say the only quirk I had was the motor polarity was reversed. Switching it on the transmitter worked but the forward was still 80% and reverse was 100%, which is backward. I flipped the motor plug around, set the transmitter back to normal and all is well.Also also if you want the shock tower to hold the goods and have a 3d printer it is on thingiverse for free from yours truly.( Roguebydesign )